/depasturation266889.html,$11,1.75mm,,PLA,Printer,3D,Filament,Bun,Industrial Scientific , Additive Manufacturing Products , 3D Printing Supplies,Upgrade,PLA,peelmontessori.com,Filament,CooBeen Ultra-Cheap Deals CooBeen PLA 3D Printer Bun Filament 1.75mm Upgrade /depasturation266889.html,$11,1.75mm,,PLA,Printer,3D,Filament,Bun,Industrial Scientific , Additive Manufacturing Products , 3D Printing Supplies,Upgrade,PLA,peelmontessori.com,Filament,CooBeen $11 CooBeen PLA 3D Printer Filament 1.75mm, Upgrade PLA Filament Bun Industrial Scientific Additive Manufacturing Products 3D Printing Supplies Ultra-Cheap Deals CooBeen PLA 3D Printer Bun Filament 1.75mm Upgrade $11 CooBeen PLA 3D Printer Filament 1.75mm, Upgrade PLA Filament Bun Industrial Scientific Additive Manufacturing Products 3D Printing Supplies

Ultra-Cheap Gorgeous Deals CooBeen PLA 3D Printer Bun Filament 1.75mm Upgrade

CooBeen PLA 3D Printer Filament 1.75mm, Upgrade PLA Filament Bun

$11

CooBeen PLA 3D Printer Filament 1.75mm, Upgrade PLA Filament Bun

|||

Product Description

filamentfilament
CooBeen PLA Filament CooBeen PLA Filament

Notes:

[TIP 1] PLA which is made from natural renewable resource (such as corn starch), no harm to user.

[TIP 2] Recommended extrusion/nozzle temperature 180°C - 210°C (356°F - 410°F), hot bed 0°C - 60°C (32℉~ 140℉) to make your experience better.

[TIP 3] please keep the filament dry and dust-free to prevent it from becoming brittle or clogging the nozzle. be sure to Insert free end of filament into holes to avoid being tangled for next time use.

Solve common problems:

●1 : clog the nozzle

A:You can solve the problem through the following methods.

1 Increase the printing temperature and reduce the printing speed to improve .

2 Reinstall the cable. You need to remove the previously used filament, use scissors to cut the melted or damaged part of the wire, and then reinstall the filament, and then see if the new, undamaged filament can be extruded.

3 Clean the nozzle. First heat the extruder to 100 degrees Celsius. Some users use the E string on the guitar to push out the nozzle in the opposite direction. If dredging does not work, you need to consider replacing the nozzle.

● 2 : The product has no stickiness and no adhesion

A:You can solve it in the following ways.

1 Please confirm whether your platform itself is flat and whether it is placed horizontally. After the platform has been leveled, you need to determine whether the starting position of the nozzle is properly spaced from the platform. Please note that if you only make small adjustments each time, the actual impact will be great.

2 The first layer is printed too fast. Please reduce the printing speed of the first layer.

3 There is a problem with the temperature or cooling settings. Please note that if you observe that the first layer sticks to the platform very quickly, but then detaches as the temperature drops, then it is probably a problem with the temperature and cooling-related settings. If you are in a relatively ventilated environment, you need to close the printer so that the wind cannot blow the prints.

4 Surface treatment of the platform. Platforms of different materials have different degrees of adhesion to different materials. Before use, check that the platform is free of dust and grease. Using water or alcohol to clean the platform will have a different effect. Many users also use glue to coat the surface of the platform, or hair gel, or other sticky substances.

5 In case of cold shrinkage, the hot bed is not heated or the temperature is too low, increase the setting temperature of the hot bed.

● 3 : The product is fragile and brittle

When the filament is stored in an exposed environment, it will gradually become brittle and affect the print quality of the product, including bubbles and spots. Although the filament is insoluble in water, its water absorption rate is very high. When exposed to air or water, the filament tends to deteriorate. Therefore, the exposed consumables should be used up within 1 month. The filament stored in a sealed container can be stored for up to 2 years. However, our recommendation is to buy and use immediately. The ideal storage method is to store in a resealable bag, avoid direct sunlight, keep the environment dry, and the temperature is neither hot nor cold. It is best to have an oven, the preservation effect will be much better.

●4 : Product wire drawing

A:The printing temperature is set too high, lower the temperature.

PLA Black PLA Purple PLA Purple TPU Black TPU Grey
PLA 1.75mm 3D Printer Filament-Midnight Black PLA 1.75mm 3D Printer Filament-Vitality Green PLA 1.75mm 3D Printer Filament-Dark Purple TPU Filament 1.75mm Flexible TPU 3D Printer Filament(Black) TPU Filament 1.75mm Flexible TPU 3D Printer Filament(Grey)
Nozzle Temp 180-210℃ 180-210℃ 180-210℃ 220-250℃ 220-250℃
Bed Temp 0-60℃ 0-60℃ 0-60℃ Need not Need not
Net Weight 1kg (2.2lbs) 1kg (2.2lbs) 1kg (2.2lbs) 1kg (2.2lbs) 1kg (2.2lbs)
High Compatibilit ✔️ ✔️ ✔️ ✔️ ✔️
Clog-Free, Bubble-Free ✔️ ✔️ ✔️ ✔️ ✔️

CooBeen PLA 3D Printer Filament 1.75mm, Upgrade PLA Filament Bun

Architecture

technology

Design

LIFESTYLE